FYB FB202 feedback suppressor
- Model
- FB202
- SKU
- FYB-531672
Two-channel acoustic feedback suppressor: 24 narrow notch filters per channel for automatic suppression of microphone howl.
On order
Price on request
Send a request. A manager will name the price and the delivery time during working hours.
Key specifications
- Power supply
- ~220 V 50 Hz
- Frequency response
- 20 Hz-20 kHz
- Dimensions
- 482 × 44.5 × 265 mm
Description
The FYB FB202 is a two-channel feedback suppressor for sound reinforcement systems with microphones. Feedback is the howl or hum that builds up when sound from the speakers gets back into a microphone and is amplified round the loop.
Suppression is automatic: a narrow notch filter is placed on the howl frequency, and the rest of the sound is barely changed.
- 24 filters per channel, 48 in total, in dynamic or static mode.
- 1 Hz filter resolution, 20 Hz – 20 kHz working range, ±10 Hz frequency shift.
- Noise gate, gain, 8-band parametric EQ and compressor in each channel.
- 32-bit floating-point DSP, 24-bit AD/DA conversion, 96 kHz.
- Inputs and outputs: two XLR and two 1/4" TRS jacks each; input impedance 40 kΩ balanced, 20 kΩ unbalanced.
- USB and RS-485 for PC software and central control.
108 dB (A) signal-to-noise ratio, dynamic range of 110 dB or more, distortion up to 0.014 %. LCD display, 220 V mains, 482 × 44.5 × 265 mm, about 2.1 kg. The suppressor goes between the mixer and the amplifier, a chain put together during audio and public address installation.
Specifications
| Processor | 32-bit floating point DSP, 24-bit AD/DA, 96K sampling frequency |
|---|
| Power supply | ~220 V 50 Hz |
|---|
| Inputs | 2 x XLR & 1/4" TRS |
|---|---|
| Input impedance | 40kΩ balanced, 20kΩ unbalanced |
| Outputs | 2 x XLR & 1/4" TRS |
| Frequency response | 20 Hz-20 kHz |
| Signal-to-noise ratio | 108 dB (A-weighted) |
| Total harmonic distortion | ≤0.014% |
| Dynamic range | ≥110 dB |
| Input sensitivity | 2Vrms |
| Output level | 1.6Vrms |
| Output impedance | 150Ω |
| Dimensions | 482 × 44.5 × 265 mm |
|---|---|
| Net weight | about 2.1 kg |
FAQ
Why is audio processor needed in PA system?
Audio processor is essential in professional PA systems for several reasons: 1) acoustic correction – EQ eliminates room acoustic problems (resonances, echo), 2) feedback prevention – automatic feedback suppressor, 3) speaker protection – limiter protects speakers from excessive power, 4) zone control – matrix routing for different zones, 5) sound quality improvement – compressor, EQ, delay.
What's the difference between analog and digital audio processors?
Analog processors use analog circuits (op-amps, capacitors) – limited functionality, manual adjustment, noise. Digital processors (DSP) use digital signal processing – unlimited functionality (EQ, compressor, echo canceller, routing), PC/Mac software control, preset storage, precise parameters, no noise. Modern systems use only digital processors.
Can audio processor integrate with Dante network audio?
Yes, modern audio processors support Dante/AES67 network audio – this allows transmitting audio signals over IP network (LAN/WAN) without analog cables. Dante network provides low latency (<1ms), high quality (24-bit/96kHz), and simple scaling (hundreds of channels in one network). Integration: Dante audio processor + Dante amplifiers + Dante microphones + Dante mixer.
Need it installed?
LAGI will deliver, install and set up the equipment and provide warranty service afterwards.