Skip to content

CCTV maintenance and what a routine check should cover

A routine check for cameras, recorder, archive and power, a five-minute owner's check and the signs that it is time to call an engineer.

4 min read

Technician on a step ladder wiping a dome camera, with a checklist tablet and a toolbox nearby

CCTV maintenance confirms three things: each camera shows what it should, the recorder keeps an archive of the right length, and the footage you need can be found and exported. Systems usually fail quietly. A camera gets knocked aside, a disk stops recording, the recorder's clock drifts by an hour, and the owner finds out on the day the footage is needed.

What fails without anyone noticing

  • A camera has been turned by the wind, by workers during renovation or by someone who did not want to be filmed.
  • Dust has settled on the dome, a spider has spun a web or a bird has left a mark, and at night the infrared turns it all into a white haze.
  • One of the recorder's disks has failed and the archive has shrunk, while the live picture looks normal.
  • Cameras were added, the archive dropped from 30 days to 12, and nobody recalculated it.
  • The recorder's clock has drifted, and footage with the wrong date is hard to use as evidence.
  • The admin password was known only to an employee who has since left.

The routine check, item by item

What we checkWhat we look for
Each camera's pictureThe view matches the design, the focus is sharp, the night illumination works
Lenses and domesDust, cobwebs, bird marks, scratches. Cleaned with a soft cloth, no abrasives, no alcohol on plastic
Mounts and housingsThe camera is held firmly, seals are intact, no moisture or corrosion inside
Cables and connectorsKinks, damaged insulation, signs of rodents, corroded outdoor connectors
Recorder disksS.M.A.R.T. status, recording errors, a growing count of bad sectors
Archive lengthHow many days are actually stored, and whether that matches what is needed
Playback and exportFinding footage from a chosen day on every camera and exporting a clip
Date and timeSync with a time server, the correct time zone
Firmware and passwordsSecurity updates, unused accounts, two-factor login in the app
PowerThe UPS battery under load, spare PoE budget, power supplies running hot
Alerts and remote accessA test event reaches the phone, the app connects

A recorder's disk runs around the clock and wears out over time. The recorder reports its health, and a disk with a growing error count is replaced early, while the archive is still intact. Our article NVR or DVR explains why an archive can end up shorter than planned and how to calculate it.

How often to check

We recommend an engineer's visit every six months. Outdoor cameras by a road, in dusty workshops or on building sites need it more often, because their domes get dirty faster. Between visits, a short check by the owner once a week is enough.

A five-minute check for the owner

  1. Open every camera in the app or on the monitor and make sure none shows a black screen or a different view.
  2. Open one camera's footage from yesterday and scroll through it. That confirms recording is running.
  3. Compare the date and time on the recorder's screen with a clock.
  4. Once a month, look at the night picture. A white haze or a bright patch points to a dirty dome or a cobweb.

When to call an engineer

  • A camera shows "no signal" or drops out from time to time.
  • Cameras reboot at night when the illumination comes on. This is often a short PoE budget or poor cable. Our article what is PoE explains why.
  • The recorder beeps, reports a disk error or keeps less footage than it should.
  • Nobody remembers the admin password.
  • After renovation or a refit, cameras are blocked or pointing the wrong way.

Maintenance and repair from LAGI

We carry out CCTV maintenance and repair to this checklist, and after the visit you get a list of what was checked, what was fixed and what should be replaced soon. Equipment and installation work we have done is covered by a warranty, with the terms set out in the contract. If something needs replacing straight away, suitable cameras and recorders are in our catalog. To arrange a check, use the quote request form.

Frequently asked questions

What does CCTV maintenance include?

Checking every camera's picture and angle, cleaning lenses and domes, inspecting mounts, cables and connectors, checking the disks and the actual archive length, testing playback and export, syncing the time, updating firmware, reviewing passwords, and testing the UPS and phone alerts. At the end you get a list of the problems found.

How often should CCTV be serviced?

We recommend an engineer's visit every six months, and more often for outdoor cameras by a road, in dusty workshops or on building sites. Between visits, the owner only needs to open all the cameras and yesterday's footage once a week. It takes five minutes and catches most faults.

How do I clean a security camera?

First blow off the dust with an air blower or a soft brush, so the glass does not get scratched. Then wipe the dome or lens with a soft microfibre cloth, slightly dampened with water or lens cleaner. Alcohol and abrasives damage plastic domes. After cleaning, check the night picture, which shows any remaining marks best.

Why does my camera show a white haze at night?

The infrared light reflects off something right in front of the lens. Most often that is dust or marks on the dome, a cobweb, a nearby wall, an eave or a branch. Cleaning the dome, removing cobwebs and turning the camera slightly so the wall or eave stays out of the edge of the frame usually fix it.

Want an engineer to look at your property?

Book a site survey: we will inspect the property and prepare a quote.